EVO ONX Web GUI#
MIIVII WEB SETTINGS Manual(Jetpack 5.x, 4.6.x ,4.5.x)#
Introduction#
MIIVII WEB SETTINGS is a graphical tool based on web,for device settings .
Provides such functions as system status detection, remote access, remote login and so on.
This manual applies to the MIIVII SETTINGS of Jetpack 5.x, 4.6.x ,4.5.x .
Access Method:#
Method1- Access shortcut on local desktop:#
1 Double-click the desktop shortcut of “MIIVII WEBSETINGS” ,open the application of MIIVII WEBSETINGS 1 The login user must have root permission . The user without root permission cannot use it .
1 Default ID : nvidia Default PWD: nvidia
Method2- Access local browser:#
1 Open local browser 1 Input http://127.0.0.1:3000 1 The login user must have root permission . The user without root permission cannot use it .
1 Default ID : nvidia Default PWD: nvidia
Method3- Access browser of client PC in same LAN:#
1 Open browser of client PC in same LAN 1 Input “ The LAN IP of device + port number”,port number is 3000 . For example http://192.168.1.100:3000 1 The login user must have root permission . The user without root permission cannot use it .
1 Default ID : nvidia Default PWD: nvidia
Function Description#
Switching between Chinese and English interface#
In the upper right corner of the page ,click the switch button , The interface can be switched between Chinese and English .
(Chinese/English switching is available from MWS V2.5.x and later versions)
System Status#
View basic information about the current system, such as CPU usage, memory usage, and storage usage.
1 Click “System Status” on the left menu bar to enter the page.
You can also view the system version on the CLI():
cat /etc/miivii_release
APEX 4.2.2-1.5.0
System Settings#
Set up basic system functions, such as system timing Settings,and so on.
SyncSettings (system timing Settings)#
1 Click the left menu bar “System Set - SYNC Set” to enter the page.
1 Choose Timing mode : NTP/GPS/NONE
2 “NTP” is the default mode. NTP network timing mode: - The device is connected to the network and timed by the NTP service. The device can be used as a synchronous source to time and synchronize the sensor. 2 “GPS” is GPS timing mode: - In this case, the device is connected to GPS and timed by GPS. The device can be used as a synchronization source to time and synchronize the sensor 2 “None” is the asynchronous mode. In this case, the device is not timed but can be used as the synchronization source. 1 Set Sync out :
2 Adjust the Sync out output frequency. Note that this is not the GMSL frequency.
“EVO NX ,EVO TX2” , “S2” don’t have the function of SYNC
“LIte xxxx” product series don’t have the function of SYNC
Configuration file path:
/opt/miivii/config/sync/sync.cfg
The timing mode is implemented by modifying the X value of “sync_type:X”.
0: GPS timing mode
1: NTP network timing mode
2: Asynchronous mode
Adjust the Sync out frequency by changing the XX value of “SYNC_out_freq :XX”. This adjustment supports only integers.
cat /opt/miivii/config/sync/sync.cfg
sync_out_freq:25
sync_type:2
/*
note:
sync_out_freq---the frequency is 25 for sync out time
sync_type---0 is for GPS calibrate time
1 is for SYS calibrate time
2 can not calibrate time
GPIO Set#
1 Click the left menu bar “System Set-GPIO Set” to enter the page. 1 Choose to set the output voltage value.
Note:Only “EVO ONX、EVO ONO” have the function of GPIO Set.
System Upgrade#
MiiVii provides OTA upgrades to equipment systems.
1 Click the left menu bar “System Upgrade” to enter the page.
1 Click “Check Upgrade” , If have new version , click “”
Device Binding#
MiiVii provides the EdgeService cloud service. Enabling the cloud service requires binding devices.
1 Click the left menu bar “Device Binding” to enter the page.
1 Bind the device as prompted. Use wechat to scan.
The log export#
System run logs are stored in logs in /var/log/,The Log Export function allows you to package and download logs to a local PC.
1 Click the left menu bar “Log Export” to enter the page.
1 Click “Export System Logs” to complete.
WEB Terminal#
MiiVii Web Settings provides the remote terminal function through the WEB
1 Click “WEB Terminal” on the left menu bar to enter the page.
1 Click “Open terminal” to open the WEB terminal (as shown below)